同步数字体系中155Mbit/s净荷的误码测试

本文基于光纤传输同步数字体系(S D H)系统的开发背景,较为详细地总结了155Mbit/s速率下的净荷误码测试机理.最后给出了净荷的误码测试方法以及误码测试系统的信号流程.     

Signal Integrity: Fault Modeling and Testing in High-Speed SoCs

As we approach 100 nm technology the interconnect issues are becoming one of the main concerns in the testing of gigahertz system-on-chips. Voltage distortion (noise) and delay violations (skew) contribute to the signal integrity loss and ultimately functional error, performance degradation and reliability problems. In this paper, we first define a model for integrity faults on the high-speed interconnects. Then, we present a BIST-based test methodology that includes two special cells to detect and measure noise and skew occurring on the interconnects of the gigahertz system-on-chips. Using an inexpensive test architecture the integrity information accumulated by these special cells can be scanned out for final test and reliability analysis.     

声诱饵仿真试验系统

介绍了声诱饵仿真试验系统的组成、工作原理、对接装置结构等,建立了对接装置声耦合状态下的数学模型,对近场声压分布进行了仿真计算,得出了匹配材料厚度、发射和接收换能器的选取原则。     

The Role of Test Protocols in Automated Test Generation for Embedded-Core-Based System ICs

Modular testing is an attractive approach to testing large system ICs, especially if they are built from pre-designed reusable embedded cores. This paper describes an automated modular test development approach. The basis of this approach is that a core or module test is dissected into a test protocol and a test pattern list. A test protocol describes in detail how to apply one test pattern to the core, while abstracting from the specific test pattern stimulus and response values. Subsequent automation tasks, such as the expansion from core-level tests to system-chip-level tests and test scheduling, all work on test protocols, thereby greatly reducing the amount of compute time and data involved. Finally, an SOC-level test is assembled from the expanded and scheduled test protocols and the (so far untouched) test patterns. This paper describes and formalizes the notion of test protocols and the algorithms for test protocol expansion and scheduling. A running example is featured throughout the paper. We also elaborate on the industrial usage of the concepts described.     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。     

插补法CAI研究

数字程序控制计算机辅助教学是将计算机技术用于数字程序控制的教学过程，它帮助学生学习并模拟教学实验．本文介绍了数字程序控制中直线插补和圆孤插补的ＣＡＩ实现方法．     

Quantitative feedback theory with applications in welding

Two different control systems were developed using quantitative feedback theory for weld quality improvement. The first application to be discussed was designed for the resistance pinch welding process and uses electrode displacement and force as feedback parameters. A correlation between weld quality and electrode displacement is established for constant electrode force. The system is capable of producing repeatable welds of consistent quality, with wide variations in weld parameters. This is the first time feedback control has been successfully applied to pinch welding. The second example presented in this paper was developed for penetration control of the gas-tungsten-arc welding process. The feedback signal is obtained by measuring the amount of light emitted from the back side of the weld. Welds of constant penetration have been demonstrated in tests with travel speeds varying from 1.5 to 6 inches per minute and with 200 per cent changes in part thickness.     

低频电脉冲采油工程设备的开发与应用

低频电脉冲采油技术是通过升压、整流、充电等电路将电能蓄积在电容器中,通过触发电路,使能量瞬时释放,在井内液体中产生震动波,作用于地层,改善地层的渗流状况,达到提高采收率的目的。Ⅰ型设备在双河油田应用11井次,成功率72%;Ⅱ型设备在古城油田应用10井次,成功率90%。主要是由于Ⅰ型设备关键部件在处理油井时要放在井下,受高温、高压的影响及井下空间的限制,设备稳定性差、寿命短、能量小、效果差;Ⅱ型设备解决了上述问题,从而提高了试验成功率。